STRENGTH ANALYSIS OF COCONUT BELT UNRAVELER MACHINE FRAME USING FEA METHOD IN SOLIDWORKS 2020
Keywords:
Strength Analysis, Machine Frame, Solidworks 2020, Finite Element Analysis (FEA), ASTM A36Abstract
The machine frame is a vital element in the coconut belt unraveling machine, serving as the main support that ensures structural stability and durability during operation. This research analyzes the strength of the machine frame using the finite element analysis (FEA) method in SolidWorks 2020 software, focusing on stresses, deformations, and factors of safety against working loads. The material used is ASTM A36 steel with a yield strength of 250 MPa. The frame model was created in SolidWorks 2020 and tested under various loading scenarios to identify critical points and stress distribution. The simulation results show that the maximum stress remains within safe limits according to the yield strength, so the frame has an adequate safety factor for machine operation. This research serves as a reference in the development of a more optimized coconut belt unraveling machine frame design. Improvement recommendations are provided based on the simulation results to improve durability and structural efficiency and minimize the risk of failure during use.
References
1232pm_9.EPRA JOURNALS 14295. (n.d.).
191000221201030 JAKA UTAMA. (n.d.).
Akuntansi, J., Keuangan, P., & Informasi, D. (2022). PENINGKATAN EKONOMIMASYARAKAT MISKIN MELALUI PEMANFAATAN LIMBAH KELAPA. 2(1), 45–61.
Astuti, F., Pratapa, S., Suasmoro, S., Triwikantoro, T., & Cahyono, Y. (2023). Pengolahan Limbah Sabut Kelapa Menggunakan Mesin Pencacah dalam Upaya Pemanfaatannya sebagai Produk
Tepat Guna di Desa Candimulyo - Dolopo - Madiun. Sewagati, 7(3). https://doi.org/10.12962/j26139960.v7i3.504
Bisono, R. M., Hafidhoh, N., & Salim, A. T. A. (2021). Strength Analysis of Frame Structure Loading in Planning Using Solidworks Static Simulation Study. In Biomedical and Mechanical Engineering Journal (BIOMEJ) e-ISSN (Vol. 1, Issue 2).
Gukop, N. S., Kamtu, P. M., Lengs, B. D., Babawuya, A., & Adegoke, A. (2021). Effect of Mesh Density on Finite Element Analysis Simulation of a Support Bracket. FUOYE Journal of Engineering and Technology, 6(3). https://doi.org/10.46792/fuoyejet.v6i3.632
Herlambang, B., & Mulyanto, T. (2020). ANALISIS KEKUATAN GATE VALVE 2 9/16 3.000 PSI AKIBAT TEKANAN FLUIDA MENGGUNAKAN FINITE ELEMENT ANALYSIS SOLIDWORKS
2018. In Journal of Mechanical Engineering and Mechatronics (Vol. 5, Issue 1).
Hestina, J., Purba, H. J., Yusuf, E. S., Betsi, F., Dabukke, M., Azhari, D., & Darwis, V. (2022).
Indonesia 2 Pusat Riset Ekonomi Perilaku dan Sirkuler. In Badan Risetdan Inovasi Nasional
(Vol. 40, Issue 1).
ISMAIL FURQANI. (n.d.).
Lay dan Patrik Pasang Balai Penelitian Tanaman Kelapa dan Palma Lain, A. M. (n.d.).
PENGOLAHAN DAN PEMANFAATAN SERAT SABUT KELAPA.
Rivani, O. A. (n.d.). PROYEK AKHIR SAMPUL RANCANG BANGUN ALAT PENGURAI SERAT SABUT KELAPA MENJADI COCOBRISTLE D3 TEKNIK MESIN JURUSAN TEKNIK MESIN POLITEKNIK NEGERI BALI 2023.
Downloads
Published
Issue
Section
License
Copyright (c) 2026 Muhammad Asyraf Alfaruqi, Muchlisinalahuddin, Jana Hafiza (Author)
This work is licensed under a Creative Commons Attribution 4.0 International License.
